Details, datasheet, quote on part number: MCT2E PARAMETER V(BR)CBO V( BR)CEO V(BRECO) IR IC(on) Collector-base breakdown voltage. IC MCT2E Optocouplers, datasheet and pin description. MCT2E price, Purchase MCT2E. The signal is applied to the LED, which then shines on the transistor in the IC. . The MCT2E series of opto-coupler devices each consist of gallium arsenide.

Author: Vudozil Melar
Country: Suriname
Language: English (Spanish)
Genre: Spiritual
Published (Last): 17 October 2008
Pages: 151
PDF File Size: 18.84 Mb
ePub File Size: 1.97 Mb
ISBN: 425-4-82585-327-2
Downloads: 76930
Price: Free* [*Free Regsitration Required]
Uploader: Doulrajas

How to use a relay November 15, When the IR led is powered the light from it falls on the transistor and it conducts. I hope you could help me with that. Connected to isolated ground.

The transistor gets base bias via phototransistor and resistor R6 R. In the Photo-transistor mode we will not be using the base pin pin 6 of the transistor; we just have to connect the anode pin of the IR LED lc 1 to the logic input which has to be isolated and the cathode pin 2 of the IR led to the ground. There pull-up resistor 1K acts as a load resistor. FREE timer simulators for electronics beginners. Easy steps for making a line following robot using Infrared LED, The components are selected in such a way that the frequency output of the astable circuit lies within the audio range.

The output will not get high mcte2 soon as the input logic is made low and vice versa. I made this project with another opto-coupler, PC and it works well. Tuesday, January 1, Another important parameter to consider while using an Optocoupler, is the rise time tr and fall time tf.


Invento 2pcs MCT2E IC – Optocoupler – 6 Pin DIP: : Industrial & Scientific

Then Pull high the collector pin of the transistor using a resistor here I have used 1K and connect the collector pin to the output of your desired logic circuit. But when the Logic input is made high, this high voltage should be a minimum of 1. How to make an FM transmitter January 26, I was wondering if you could help me with the following.

From Latch up circuit using and optocouplerJuly 16, Review of PCBWay after-sale service.

IC MCT2E Optocouplers

When switch S2 is pressed, the base of the transistor connects to the ground 0V and resets the timer bringing Pin 4 to LOW state. TL — Programmable Reference Voltage. Opto-coupler, MCT2E is is used for latching the alarm. Log into your account. Clap switch December 18, Out of which the Phototransistor mode is mostly used, so let us look at that mode first.

The below waveform shows the time taken for the output to transit from one state to another. More details can be found at the MCT2E datasheet which is available for download at the end of this page.

Flasher circuit using NE timer- Basic electronic project.


Digital object counter DIY kit Oc 1, This will short the collector and emitter and hence the Logic Output voltage will become zero. This disables the alarm.

This is the logic output pin 6 Base B Kct2e pin of the Transistor. Light activated police siren using timer and light dependent resistor LDR. Building a circuit on a breadboard November 8, Toggle switch using This IC is used to provide electrical isolation between two circuits, one part of the circuit is connected to the IR LED and the other to Photo-transistor.

The digital signal given to the IR LED will be reflected on the transistor but there will be no hard electrical connection between the two. This way the logic input will be reflected at the logic output and still provides and isolation between the two.

How to make one transistor FM transmitter on a stripboard- page How to use the DIY clap switch September 16, Auto-Detection l Bluetooth l Smart Multimeter. The NE timer is configured in astable mode.

MCT2E IC Pinout, Specifications, Equivalent, Working & Datasheet

The Emitter pin 4 is grounded. Blinker using arduino and Mcct2e timer IC. Base pin of the Transistor. HiFirst of allthank you for your circuit above.