ASTM D5511 PDF

ASTM D is a standard test anaerobic biodegradation test method for determining anaerobic biodegradation of plastic materials under high-solids. ASTM D Standard Test Method. D Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under. High-Solids. ASTM D Significance and Use. Biodegradation of a plastic within a high- solids anaerobic digestion unit is an important phenomenon because it will affect .

Author: Akihn Aragal
Country: Iraq
Language: English (Spanish)
Genre: Science
Published (Last): 22 June 2006
Pages: 255
PDF File Size: 2.4 Mb
ePub File Size: 15.92 Mb
ISBN: 254-5-91842-579-7
Downloads: 4437
Price: Free* [*Free Regsitration Required]
Uploader: Dik

Biodegradation of plastics could allow for the safe disposal of these plastics through aerobic and anaerobic solid-waste-treatment plants. Aztm, results shall not be extrapolated past the actual duration of the test.

The test is allowed to run for as long as desired. If the positive control which contains cellulose continues to exhibit biodegradation then the test is considered valid and the inoculum considered alive. The test materials are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste. Depleting the oxygen in the incubation vessels after an initial burst of aerobic activity. Specific hazards d5511 given in Section 8. aztm

Reports shall clearly state the percentage of net gaseous carbon generation for both the test and reference samples at the completion of the test. Link to Active This link will always route to the current Active version of the standard. More specifically, the procedure is intended to create a standard laboratory environment that will permit a rapid and reproducible determination of the anaerobic biodegradability under high-solids digestion conditions.

Then, the anaerobic bacteria begin to multiply and colonize in the vessel. Note 1—This test method is equivalent to ISO Work Item s – proposed revisions of this standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

However, it is expected to resemble the environment of a high-solids anaerobic-digestion process operated under optimum conditions. Furthermore, results shall not be extrapolated past the actual duration of the test. Placing the samples in incubation vessels after the inoculum is prepared. The test materials are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste.

  ENTE RINNI CHECHI PDF

As these bacteria begin to utilize the carbon in the test samples, they produce carbonaceous gasses such as CO2 and CH4.

ASTM D – Anaerobic Biodegradation | Situ Biosciences LLC

This procedure has been developed to permit the determination of the rate and degree of anaerobic biodegradability of plastic products when placed in a high-solids anaerobic digester for the production of digestate from municipal solid waste. This is often sludge from a water d511 plant mixed with a certain percentage of solid material from composting facilities.

When the test is run to satisfaction, final carbon and methane gas readings are recorded and the incubation vessels are emptied and the samples are cleaned and weighed. Reports shall clearly state the percentage of net aatm carbon generation for both the test and reference samples at the completion of the test.

Placing the sample materials in an inoculum derived from anaerobic digesters operating on household waste.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. These gasses are measured daily and the results are carefully recorded.

The molar weight of the total gas produced by the test samples is calculated and compared to the carbon weight of the original samples and the percent biodegradation of the samples can then asttm determined.

The procedure is intended to create a standard laboratory environment that will permit a rapid and reproducible determination of the anaerobic biodegradability under high-solids digestion conditions. This inoculum contains methanogenic bacteria that are also found in landfills.

BioPro Global – ASTM D

It is the responsibility of the user of this standard to establish appropriate astj, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Biodegradation of a plastic within a high-solids anaerobic digestion unit is an important phenomenon because it will affect the decomposition of other waste materials enclosed by the plastic and the resulting quality and appearance of the digestate after an anaerobic digestion process. Specific hazards are given in Section 8. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  INTERCAL MANUAL PDF

Historical Version s – view previous versions of standard. Three vessels are used for each sample, and one negative control and one positive control awtm prepared as well. They are kept within strict temperature and moisture tolerances. This test method also resembles other anaerobic conditions where the gas generated is recovered and biogas adtm is actively promoted by inoculation for example, codeposition of anaerobic sewage sludge, anaerobic leachate recirculationmoisture control for example, leachate recirculationand temperature control for example, short-term injection of oxygen, heating of recirculated leachate 5, 6, 7.

Reports shall clearly state the percentage v5511 net gaseous carbon generation for both the test and reference samples at the completion of the test. The vessels are r5511 and are not exposed to UV radiation. The testing process includes: Aatm values given in SI units are to be regarded as the standard. This test method determines the degree and rate of biodegradation of plastic materials in an oxygen-free anaerobic environment.

Work Item s – proposed revisions of this standard. This test method is designed to be applicable to all plastic materials that are not inhibitory to the microorganisms present in anaerobic digesters operating on household waste.

ASTM D5511 – Anaerobic Biodegradation

Active view current version of standard. Link to Active This link will always route to the current Active version of the standard.

Furthermore, results shall not be extrapolated past the actual duration of the test.