KX mL ( US gt). KX | mL ( US gt). Depending on the atmospheric temperature of your riding area, the transmission oil viscosity should . Kawasaki. KX KX Motorcycle Service Manual This quick reference guide will assist you in locating a desired topic or procedure. • Bend the pages back. KX specs Completely redesigned for , the KX has received a number of . Kawasaki Kx Service Manual Repair Kx

Author: Vudolabar Bagore
Country: Mozambique
Language: English (Spanish)
Genre: Marketing
Published (Last): 2 May 2016
Pages: 342
PDF File Size: 1.78 Mb
ePub File Size: 4.82 Mb
ISBN: 419-4-28557-699-9
Downloads: 25670
Price: Free* [*Free Regsitration Required]
Uploader: Akigal

Run the clutch cable above the number plate mounting bracket. Page of Go. Rebound Damping Adjuster Setting Check both top plug O-ring [C] for damage and replace them if necessary.

The drive shaft gears can kawasakk identified by size; the smallest diameter gear is 1st gear, and the largest is 5th KX or 6th KX It Cylinder head warped is meant simply as a rough guide to assist Cylinder base gasket damaged the troubleshooting for some of the more Read valve damaged KX If the gap is incorrect, adjust it see this chapter.

Mating section on the clamp at outside. Loosen the crankshaft sensor screws [A]. Year of Publication see all.

KX Motorcycle Repair Manuals & Literature for sale | eBay

Skip to main content. Right Radiator sprocket cover and run them along with 4. This prevents them from being moved out of their proper posi- tion, should the brake lever be squeezed accidentally.


Also, check to see that each cotter pin is in place and in good condition.

2004 Kawasaki KX125 (KX125-M2) OEM Parts

Friction Plate Thickness KX If the surface is corroded, or if the blades [B] are dam- aged, replace manuzl impeller. Front Fork Guard 7.

Tighten all snugly, then loosen, retighten to 4. Exhaust pipe leaking at cylinder head con- Clutch lever play excessive nection Clutch plate warped or too rough Crankshaft runout excessive Clutch spring tension uneven Engine mounts loose Transmission oil deteriorated Crankshaft bearing worn Transmission viscosity too high Primary gear worn or chipped Transmission oil level too high Clamps Install the magneto lead from this side Air, however, is easily compressed.

Torque – Caliper Bleed Valve: Front Brake Caliper Piston Ring, Piston Ring Groove Inspection If the ring has worn down to less than the service limit, replace the ring; if the groove width exceeds the service limit, replace the piston.

Kawasaki KX KX Service Manual – How-To Motorcycle Repair

Overall Width mm Never used, no scratches but may not be quite perfect due to age. Torque – Magneto Cover Bolts: Clutch Lever Free Play Check Mikuni TMX carburetor helps boost mid-range and top-end power.

Comments 200 this Manuals Your Name.


Such a shock to the parts can damage them. Kawasaki KX Service Manual pages. Page 48 Then push down and turn it further in the same direction and remove the cap. Page 92 Service Fuel Level above the bottom edge of the carb.

Service Repair manual for Model years: Head Pipe Outer Race Driver, Apply high temperature grease. If there is any doubt as to the condition of them, replace them with new ones.

Kawasaki KX125 Service Manual

Page The output shaft gears can be identified by size; the largest diameter gear is 1st gear, and the smallest is 5th KX or 6th KX Special Tool – Jack: Crankshaft bearing worn or damaged Firing incorrect: Change the coolant in accordance with the Periodic Maintenance Chart see Periodic Maintenance chapter.

Page Remove the plug and the pad bolt [A]. Check and balance the wheel when a tire is replaced with a new one.

Idle Adjusting Screw B. If the slow jet is damaged, replace it with a new one. UPC Does not apply.